Development and Application of Aluminium CNT Composite Electrode for Electro Discharge Machining

dc.contributor.guideMondal, Subhas Chandra
dc.coverage.spatial
dc.creator.researcherKundu, Subham
dc.date.accessioned2026-02-03T11:37:31Z
dc.date.available2026-02-03T11:37:31Z
dc.date.awarded2025
dc.date.completed2025
dc.date.registered2018
dc.description.abstractAluminium Metal Matrix Composites (Al-MMCs) are widely utilized in industry. This thesis presents a novel multistage ball milling (MSBM) technique for fabricating Al-MMCs via powder metallurgy (PM), incorporating 5 wt. % copper (Cu) and 0.5 1.5 vol. % CNTs. The five samples named as PM-Al, PM-Al-5Cu, PM-Al-5Cu-0.5 CNT, PM-Al-5Cu-1.0 CNT, PM-Al-5Cu-1.5CNT were prepared twice by conventional single-stage ball milling (SSBM) and new MSBM technique. The MSBM approach utilizes sequential mixing at different milling speeds to optimize CNT distribution and reduce structural degradation. Comparative analysis against SSBM revealed that the MSBM-processed Al-5Cu-0.5CNT composite exhibited superior electrical conductivity, thermal conductivity, and hardness. The developed MSBM processed Al composites are applied as electrode for the surface modification of Inconel 718 using Electro-Discharge Machining (EDM). Compared to cast copper electrodes, PM processed CNT reinforced Al-MMC electrodes achieved higher material transfer to the workpiece and notable changes in Inconel s surface composition, including increased deposition of Al, Cu, and Carbon (C), alongside reduced Nickel (Ni), Ferrous(Fe), and Chromium (Cr) content. Surface hardness improved maximum with the PM-Al-5Cu-1.5CNT electrode, while the PM-Al-5Cu-0.5CNT electrode yielded the best surface finish. The process capability analysis of PM processed Al, Al-Cu and Al-Cu-CNT EDM electrodes were done with newly developed univariate index (AI, Adev, Ca). Material removal rate (MRR), tool wear rate (TWR) and post EDM hardness were analyzed and compared with conventionally used Cast-Al and Cast-Cu electrodes. It was observed that among PM processed electrode Al-Cu was suitable for highest MRR, Al-Cu-0.5 CNT was suitable for lowest TWR, and all electrodes met specification limits for post EDM hardness. newline newline
dc.description.note
dc.format.accompanyingmaterialDVD
dc.format.dimensions
dc.format.extent
dc.identifier.researcherid0000-0002-7958-5667
dc.identifier.urihttp://hdl.handle.net/10603/692100
dc.languageEnglish
dc.publisher.institutionMechanical Engineering
dc.publisher.placeShibpur
dc.publisher.universityIndian Institute of Engineering Science and Technology, Shibpur
dc.relation
dc.rightsself
dc.source.universityUniversity
dc.subject.keywordEngineering
dc.subject.keywordEngineering and Technology
dc.subject.keywordEngineering Mechanical
dc.titleDevelopment and Application of Aluminium CNT Composite Electrode for Electro Discharge Machining
dc.title.alternative
dc.type.degreePh.D.

Files

Original bundle

Now showing 1 - 5 of 13
Loading...
Thumbnail Image
Name:
01_title.pdf
Size:
213.31 KB
Format:
Adobe Portable Document Format
Description:
Attached File
Loading...
Thumbnail Image
Name:
02_prelim pages.pdf
Size:
2.57 MB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
03_content.pdf
Size:
363.31 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
04_abstract.pdf
Size:
181.32 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
05_chapter 1.pdf
Size:
224.61 KB
Format:
Adobe Portable Document Format

License bundle

Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
license.txt
Size:
1.79 KB
Format:
Plain Text
Description: